ACE0 4km Grafische TDR



Bestel
The add to cart button will appear once you select the values above
Detail

The ACE0 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-4000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128x64 pixel back light Liquid Crystal Display. The Auto Fault Location key will move the cursor directly to the first event or fault, thus eliminating the need to visually interpret the wave form. When set in manual mode, the wave form may be visually scanned as on conventional TDRs. In both modes the user variable gain covering the range of default to 64 db’s may be used to magnify small events identified on the waveform. The scan lock feature will allow the user to hold the trace for closer examination. Designed for identifying and locating faults on all metallic cables with two or more insulated conductors. The ACE0 has impedance matched circuits for 25, 50, 75 and 100 ohms and with velocity of propergation settings from 1-99% (or the equivalent in feet or meters/micro second) will cover the range of power, data, communication and CCTV cables. Housed in a rugged IP54 rated ABS enclosure and weighing only 350 grams (12 ounces). Also contains a tone generator for wire tracing, for this function an optional receiver is required.

Kenmerk
  • Auto Fault Location
  • Rugged Palm-Top design
  • Weighs less than 350 grams
  • 11 Measurement Ranges up to 4000m(4km)
  • 25, 50, 75 & 100 Ohm Selectable Cable Impedance
  • User Variable Gain Control
  • Built in Tone Generator for Pair Tracing and Identification
  • Suitable for testing all Communication and Power Cables
  • Environmental Protection IP54
Specificatie
Length: 4km
Impedance: 25, 50, 75 & 100 Ω
Dead zone: 0.5 meter
Ranges Meters Kilometers: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
Range step: 11
Accuracy: 1% of selected range*
Resolution: Approximately 1% of range
Range selection: Manual & Automatic
Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP
Output Pulse Width: 3 ns to 3 ms, connected to range setting
NVP VoP Velocity Factor: Adjustable from 1% to 99%
Scan Rate: 2 scans / second or scan held (not on 3km/4km range)
Output Pulse: 5 volts peak to peak. Into open circuit
Tone Generator: 810 - 1100Hz
Connector: 2x Banana chassis
Display: 64 x 128 pixel
Backlight: Yes
Voltage Protection: 250 volts AC
Battery Life: 60 hours continuous scanning
Power Supply: 6 volts 4 x 1.5 AA Alkaline cells
Power Down: Selectable 1, 2, 3, 5 minutes or disabled
Operating Temperature: -10° / 50°C
Storage Temperature: -20° / 70°C
Dimensions: 165 x 90 x 37 mm
Weight: 350 grams
Standards: IEC 61010-1
  EN 60950
  ISO9001
EMC BS/EN: 61326-1
Water/Dust Proof: IP54
Goedkeuring: CE, RoHS en WEEE

* Measurement accuracy of <+/- 1% assumes the instrument
setting for velocity of propergation (Vp) of the cable under test to be
accurately set, homogeneity of the Vp along the cable length,
and accurate cursor positioning.
Content
- Main unit
- AJJ4 Tas ACE0/ACE1/ACE2/GT21/GT22
- AJJ3 Banaan naar krokodilbek ACE0/ACE1/ACE2
- Engels Gebruiksaanwijzing
Optie
- CU03 Cursus analoge telefonie en ondergrondse netwerken
- KO10 Instrumentkoffer medium (105 mm)
- ON80 Ontvanger 9001
Prijs
896,61 € (741,00 € excl VAT) each

Prijzen zijn per stuk, exclusief 21% BTW en gelden voor levering af magazijn Voorthuizen. Bij levering in Nederland of in België worden verzendkosten altijd in rekening gebracht tot maximaal EUR 25,00. Ditzelfde geldt voor expreskosten en/of rembourskosten. Bij de producten trainingen en cursussen is na het bevestigen van de cursusdatum, bij het niet verschijnen van de deelnemer(s), de verplichting ontstaan tot volledige betaling. Het volgen op een latere datum ingeval van niet verschijnen is in overleg mogelijk, maar wordt uitsluitend gezien als service. Hieruit kan geen enkel recht uit worden onttrokken.